電加熱反應釜在使用之后會出現什么故障
發布時間：2017-11-28 9:32:22 來源: 瀏覽次數：
摘要：電加熱反應釜任何機械設備在操作使用過程中，難免會因?yàn)橐恍┎缓侠淼牟僮鞫鴮?dǎo)致設備出現故障，影響設備的正常使用生產
電加熱反應釜任何機械設備在操作使用過程中，難免會因?yàn)橐恍┎缓侠淼牟僮鞫鴮?dǎo)致設備出現故障，影響設備的正常使用生產。下面我們就電加熱
反應釜在使用過程中出現的一些常見故障及其解決方法給大家做個總結。 Any mechanical equipment in the operation and use
process, it is inevitable because some unreasonable operation and lead to equipment failure, affect the normal use of equipment
production. Below we on the electric heating reactor in the process of using the emergence of some common faults and solutions
to everyone to make a summary. 電加熱反應釜常見故障一：外磁鋼旋轉內磁鋼不轉，電機電流減小。 故障原因：釜內溫升過高，冷卻循
環不暢，內磁鋼因高溫褪磁，從而引起內磁鋼不轉。 加氫反應，內磁鋼套有裂紋，內磁鋼膨脹。 故障解決方法方法：此時需聯系供貨商，
要重新更換內磁鋼。 Common faults one: outside the magnet rotating magnet does not turn the motor current is reduced.
Failure reason: the temperature rise in the kettle is too high, the cooling circulation is not smooth, the internal magnetic
steel is high temperature fading, which causes the internal magnet not to rotate. The hydrogenation reaction, the magnet sleeve
crack, magnet expansion. Methods: the need to contact the supplier to solve the fault, to replace the magnet. 電加熱
反應釜常見故障二：閥門出現泄漏。故障原因：閥桿、閥口密封面損傷導致泄漏。 故障解決方法：維修或更換閥桿閥口。 Common
faults two: valve leakage. Failure: valve stem, valve sealing surface damage due to leakage. Troubleshooting: repair or
replacement of the valve stem. 電加熱反應釜常見故障三：密封面出現泄漏。故障原因：螺桿螺紋松動或密封面損傷。 故障解決
方法：當發現螺桿螺紋松動是須將螺桿重新上緊即可，如果是密封面受損則需要重新修磨拋光密封面。 Common faults three: leakage
occurred on the sealing surface. Fault: loose or damage on the sealing surface of screw thread. Fault solution: when the
screw thread is loose, it is necessary to tighten the screw again. If the sealing surface is damaged, it is necessary to re
polish and polish the sealing surface. 電加熱反應釜常見故障四：磁力耦合傳動器內有摩擦的噪音，影響設備工作生產。故障原因：
軸套、軸承磨損、間隙過大、內磁鋼轉動出現跳動。 故障解決方法：需要與供貨商聯系，更換軸承和軸套。 Common faults four:
magnetic coupling in friction noise, affect the equipment production. Fault: shaft, bearing wear, the gap is too large, the
magnet rotation appears beating. Troubleshooting method: need to contact the supplier and the replacement of bearings and
bushings. 以上就是電加熱反應釜在使用中常見的故障及問題，如出現以上情況，可以按照以上方法進行維修處理，也歡迎大家來電咨詢。
The above is the electric heating reactor in the use of common faults and problems, such as the above situation, can be in
accordance with the above methods for maintenance, also welcome to inquire.
上一篇我們送上的文章是電加熱反應釜怎么樣可以達到好的密封效果為了更加全面的介紹反應釜加熱器、電加熱反應釜、遠紅外反應釜、遠紅外加熱器等產品，我們將持續發布最新知識，幫助大家了解更多的信息。 在下一篇繼續做詳細介紹，如需了解更多，請持續關注。
本文由生產廠家揚中市金元化工電力設備廠于2017-11-28 9:32:22整理發布。
轉載請注明出處：http://www.boxinlai.com.cn/news/2820.html。
上一篇：電加熱反應釜怎么樣可以達到好的密封效果
下一篇：反應釜都是怎么根據應用分類的
